Getting started

FEA Offshore is a Windows desktop program. It shares its window with FEA Studio: the 3D view, the Explorer, Properties, the Output panel and the Chart. The offshore tools are on two menus.

MenuGroups
OffshoreGuide (Workflows), Environment, Sea states, Members, Topside, and the submenus Floating and Renewables
Offshore designLoad cases, Analysis, Floating, Design, Ultimate, Seismic, Foundations, Installation, Fatigue

FEA Offshore holds three engines: the FEA solver for structures, NEMOH for floating hulls and OpenFAST for wind turbines. Analysis › Choose the analysis… asks what you want to analyse, names the engine and lists the inputs it needs, each with its command and whether the project has it yet. Analysis › Run analysis (F5) then runs that engine.

AnalysisEngineFor
Fixed structureFEA solverA jacket, monopile or tripod on the seabed: storm waves and current, code check, fatigue, seismic, pushover
Floating hullNEMOHA spar, semi-submersible or barge in waves: added mass, damping, wave forces and motions (RAOs)
Wind turbineOpenFASTA turbine on land, a monopile, jacket or floater: wind, waves, structure and control together, IEC load cases

For a step-by-step start, open Offshore › Workflows (F1). It has three guided workflows: a fixed jacket, an offshore wind monopile and a moored floating body. Each step has buttons for its commands and ticks itself when done. The panel also opens on the first start.

File › Open takes an FEA project (.fea), an OpenFAST model (.fst) or a NEMOH project (Nemoh.cal). One project holds them together.

Once a study has results the model locks. Unlock model removes the results so you can edit again.

Samples

Open them from File › Samples. Each one is complete, with its studies ready to run.

SampleWhat it shows
Four-leg jacketTubular jacket on piles in 60 m of water. 100-year Stokes wave (H 18 m, T 14 s) with current, marine growth and 38 m/s wind, from four directions; wave-in-deck; API RP 2A-WSD check.
Offshore wind monopile6 m monopile in 25 m of water, sand over clay with PISA springs, 5 m tower to a 90 m hub. Wave, Modal and Dynamic studies; ISO 19902.
Moored floating sphere5 m floating sphere (builtin:sphere.h5) on three chains in 2 m, 6 s waves. Dynamic and Nonlinear studies.
OC4 DeepCwind semi-submersibleNREL 5 MW on the OC4 semi-submersible in 200 m of water, three 835 m chains, JONSWAP sea and a turbulent wind with the rotor coupled two-way to OpenFAST AeroDyn.
IEA 15 MW VolturnUS-SIEA 15 MW turbine on a VolturnUS-S-like hull (Capytaine BEM data), three 850 m chains, thrust-curve rotor. Dynamic, RAO and Nonlinear studies.
RM3 wave energy converterTwo-body point absorber with a linear PTO (WEC-Sim's WAMIT data). PTO power, RAOs and the power matrix.

The bundled BEM files are builtin:sphere.h5 and builtin:deepcwind.h5 (from HydroChrono), builtin:volturnus.h5 (computed with Capytaine; for demonstration, not design) and builtin:rm3.h5 (from WEC-Sim).

Environment

Offshore › Environment creates the environment of the project. Members below the still-water level then get buoyancy and Morison wave and current loads, and the sea and seabed appear in the 3D view.

FieldMeaning
Design codeAPI RP 2A-WSD, API RP 2A-LRFD, ISO 19902, NORSOK N-004, DNV-ST-0126 or KDS 64. It sets the member and joint checks, the default coefficients and the study load factors.
Water depthFrom the still-water level (MSL) to the seabed
MSL elevation (global Z)Z of the still-water level. The seabed is at MSL minus the depth.
Water densityDefault 1025 kg/m³. Use the density of your BEM data for floating bodies.

Click the Offshore folder in the Explorer to edit the environment in Properties. The Hydrodynamic coefficients group holds Cd and Cm for clean members and for members with marine growth (the description shows the code's defaults), the wave kinematics factor (reduces wave velocities for directional spreading; API: 0.85–0.95, 1.0 for long-crested waves) and the current blockage factor (reduction of the current inside a jacket; API: 0.7–0.9). Offshore › Remove removes the water, sea states, soil and floating bodies; member settings on curves are kept.

Current, marine growth and wind

Current

Offshore › Current sets the speed at the surface and at the seabed, the heading (towards) and the profile: Power law (1/7), Linear or None (remove). The current is added to the wave particle velocities. Current stretching in the Offshore folder's Properties stretches the profile to the instantaneous surface under crests and troughs (API RP 2A §C2.3.1b(2), linear stretching).

Marine growth

Offshore › Marine growth adds a zone: thickness on the radius, from and to height above MSL, and density. Zones can be added to the existing ones or replace them. Growth makes members thicker, uses the rough Cd and Cm, and adds weight and mass.

Wind

Offshore › Wind sets the 1-hour mean speed at 10 m, the heading, the profile (NPD (API / ISO) or Power law with its exponent), the static averaging time (3 s gust for individual members, 60 s sustained for global loads with waves, 3600 s mean), and the gusts in Dynamic studies (None, NPD spectrum or Kaimal spectrum). Wind acts on dry members and on wind areas.

Design waves

Offshore › Design wave adds a regular wave: name, wave theory, height H, period T and heading (towards).

Wave theoryUse
Airy (linear)Small waves
Stokes 5th orderSteep waves in deep water
Stream functionAny depth, including steep waves in shallow water

A sea state's Properties show its wave length, steepness H/L (breaking limit about 0.142·tanh(kd)) and relative depth d/L. They also hold the Doppler shift (T is the apparent period on the current, API RP 2A §2.3.1b(1)) and the stretching above MSL for linear kinematics: Wheeler (recommended), linear extrapolation or none.

Offshore › Wave kinematics… shows the flow of a sea state around the structure: arrows and a slice on a grid from the mudline to the surface, using linear (Airy) kinematics with Wheeler stretching and the current. Remove wave kinematics clears it.

Irregular seas

Offshore › Irregular sea adds a random sea for time-domain (Dynamic) studies.

FieldMeaning
SpectrumJONSWAP or Pierson–Moskowitz
Significant height Hs, peak period TpThe sea state
Peak enhancement γJONSWAP peak factor (γ = 1 gives Pierson–Moskowitz)
HeadingDirection the waves travel towards
Spreading exponent scos-2s directional spreading; 0 = long-crested
Swell Hs, Tp and directionA second (swell) component; Hs 0 = none
Random seedSame seed, same sea

Offshore design › Extremes takes metocean extremes per return period (Hs, Tp, Hmax, THmax, current, wind) and can create a design wave from one of them. Offshore design › Metocean takes the wave scatter diagram per direction and the fatigue design life.

Morison loads and member settings

Wave and current loads on members use the Morison equation normal to the member, integrated over the wetted length: a drag term ½ρCd·D·|u|u and an inertia term ρCm·A·a. In Dynamic studies the velocity is relative to the moving member. Buoyancy acts on the wetted length with the instantaneous surface.

Select member curves to set their offshore behaviour. The curve's Properties have an Offshore group:

SettingEffect
Hydrodynamic loadsWave and current loads and buoyancy where the member is in water
Flooded (Offshore › Flooded)Water inside: no buoyancy of the bore, no hydrostatic collapse check; the water adds mass
ShieldedNo wave load (for example conductors inside guides); buoyancy still acts
Marine growthWhether the growth zones apply to the member
Pile (soil springs) (Offshore › Piles)Soil springs below the mudline

Members also hold their own Cd and Cm and the effective length factor K used by the buckling checks. In Modal and Dynamic studies the hydrodynamic added mass ρ(Cm−1)A, the water inside flooded members and the marine growth are lumped at the nodes.

Topside wind and decks

Select deck nodes, then:

  • Offshore › Wind area adds a lumped wind area (topsides, equipment): projected areas facing X and Y, centroid height above MSL and shape coefficient Cs (API RP 2A §2.3.2e: 1.0 overall projected area, 1.5 sides of buildings).
  • Offshore › Deck adds a deck for wave-in-deck loads (API RP 2A §17): underside and top above MSL, plan extent, and equipment (heavily or moderately equipped).

Soils and pile springs

Offshore › Soil layer adds a clay or sand layer below the mudline. Each new layer starts at the bottom of the previous one.

SoilFields
ClayTop and bottom depth, submerged unit weight γ′, undrained strength cu at top and bottom
SandTop and bottom depth, γ′, friction angle φ, relative density (very loose to very dense; API RP 2A Table 6.4.3-1)

Curves marked as piles get springs at every node below the mudline. Choose the Pile soil model in the pile's Properties:

  • API p-y / t-z / q-z: lateral p-y (Matlock soft clay; API sand), shaft friction t-z and end bearing q-z, after API RP 2A-WSD §6.7–6.8.
  • PISA (monopile): lateral load, distributed moment, base shear and base moment springs (Byrne et al. 2020, Burd et al. 2020). It needs the small-strain shear modulus G0 in the soil layers. The Offshore folder's PISA clay calibration chooses Cowden till (stiff) or Bothkennar (soft clay).

Cyclic p-y curves in the Offshore folder's Properties use API RP 2A cyclic p-y: Matlock cyclic clay, A = 0.9 for sand (storm loading).

A structure on piles needs no fixed supports: the springs hold it.

Studies

Studies are listed under Explorer › Studies. Select one and press F5, or use the commands on the Offshore design and Analysis menus. Running another study keeps the earlier results. A study's options are in its Properties.

StudyWhat it does
WaveSteps a regular design wave through the structure (quasi-static), with current, buoyancy and marine growth, at a number of positions over one period (default 36, every 10°). Linear models are solved at every position; models with soil springs or mooring lines at the positions of maximum base shear and overturning moment. Permanent and environmental load factors (ISO 19902: 1.1 and 1.35; NORSOK ULS-b: 1.3 environmental; API WSD: 1.0). Can run a list of design cases.
ModalNatural frequencies and mode shapes, with the hydrodynamic added mass and the soil springs
Linear dynamic (Dynamic)Time domain with a sea state: ramp time, start from still-water equilibrium, HHT or implicit Euler integrator (implicit Euler is the default with floating bodies), added mass on or off, mooring line solver, broken lines, a line failure at a given time, and the radiation memory (convolution or state space) of floating bodies
Nonlinear staticLarge-displacement static analysis. Gives the mooring pretension with floating hulls held in place.
TransferMember-force and base-shear transfer functions in waves for given headings and periods (default 3 to 22 s), with drag linearized at a wave height; quasi-static or dynamic with a damping ratio. Input to spectral fatigue.
RAOResponse amplitude operators of the floating bodies in the frequency domain: BEM added mass, damping and excitation, hydrostatics, mooring stiffness about the still-water equilibrium, linear damping, and PTOs
OffsetMooring offset curves: restoring force and line tensions at increasing offsets, for given headings, largest offset and steps
SpectrumResponse spectrum: modes, CQC, SRSS or 100-30-30 combination of directions, direction factors
PushoverPushes the structure to collapse with plastic hinges at member ends and mid-span, with a bow imperfection; design wave or point load pattern; gives the reserve strength ratio (ISO 19902 §12)

Results

Displacement, Member forces, Animate and the Results panel work as in FEA Studio. The Chart adds offshore charts when the results have them:

  • Wave loads: base shear, overturning moment and wave elevation over one period.
  • Design cases: maximum base shear, overturning moment or wave-in-deck load per case.
  • Offshore (Dynamic): hydrodynamic base shear, fairlead tensions, body surge, heave and pitch, wave elevation.
  • Transfer functions, RAOs, Offset curves, Pushover curve, Modal participation, PTO power, and Rotor charts for wind turbines.

Design cases

Offshore design › Storm cases creates design cases from a design wave in several directions, and a Wave study that runs them.

FieldMeaning
Design waveOne of the regular sea states
Categoryextreme, operating or abnormal. API WSD gives extreme and abnormal cases the one-third allowable stress increase.
Directions4, 8, 12 or 16, from a first direction
Current factorThe current turns with the wave
Wind speed at 10 mCollinear wind; 0 = none
Permanent and environmental load factorsPer case

Offshore design › Case results shows the maximum base shear, overturning moment and deck load of each case.

Code checks

Offshore design › Code check checks the tubular members (Pipe profiles) and the simple tubular joints (K, T/Y and X) on the results that are shown, enveloped over all wave positions of a Wave study. The code is the one of the environment. Utilization colours the members; Check table lists members and joints, highest first.

CodeMembersJoints
API RP 2A-WSDAxial, bending, combined and hydrostatic checks; one-third increase for extreme and abnormal casesPunching shear (static strength of simple joints, §4.3)
API RP 2A-LRFDSection D resistances with φ factorsSame formulation with the code's factors
ISO 19902§13.2 single actions, §13.3 combined, §13.4 combined with hydrostatic pressure§14.3
NORSOK N-004§6.3, material factor depending on slenderness§6.4.3
DNV-ST-0126Monopile and tower cans with DNV-RP-C202 shell and column bucklingNORSOK N-004 §6.4.3 formulation with γM = 1.15
KDS 64ISO 19902 formulas with configurable partial resistance factorsSame formulation with its factors

KDS 64 factors

FEA Offshore applies the ISO 19902 resistance formulas for KDS 64, with ISO 19902's factors by default. Confirm the resistance factors, and the load factors of the load combinations, against the KDS 64 text before use.

If a member fails, unlock the model, choose a larger section or change K, and run the study again.

Fatigue

Offshore design › Fatigue checks tubular joints, member ends and mooring lines from the shown results. The method follows the results:

Shown resultsMethod
Transfer studySpectral, with the scatter diagram (Metocean); Dirlik (broad band) or Rayleigh (narrow band) stress ranges
Wave study with fatigue casesDeterministic. Fatigue waves creates the cases from the largest wave, waves per year, Weibull shape, height blocks and directions.
Dynamic studyTime domain

The dialog sets the design life, the design fatigue factor, the S-N curve of tubular joints (DNV T or API WJ), the detail class and SCF of member ends (girth welds), the splash zone, and the mooring line type and diameter. Fatigue colours colours members by DFF × damage; Fatigue table lists hot spots and mooring lines with their fatigue lives.

Seismic and ultimate

  • Offshore design › Spectrum defines the seismic design spectrum (ISO 19901-2 / API RP 2EQ or KDS 17) and its Spectrum study. Solve spectrum runs it.
  • Accelerogram imports a ground acceleration record for a Dynamic (time-history) study.
  • Pushover pushes the structure to collapse with plastic hinges for the reserve strength ratio (ISO 19902 §12).
  • Ship impact checks a ship impact on the selected tubular member: local denting (NORSOK N-004 A.3) and a pushover study.
  • Blast applies a blast pressure pulse to the selected nodes as a load history of a Dynamic study.

[CONFIRM WHETHER THE RELEASED FEA OFFSHORE INCLUDES THE OPENSEES LINK: JACKET PUSHOVER / RESERVE STRENGTH, NONLINEAR PILE SPRINGS AND THE DUCTILITY-LEVEL EARTHQUAKE WITH THE USER'S OWN OPENSEES]

Mudmats and driveability

  • Offshore design › Mudmat adds a mudmat under the selected support nodes. Mudmat check checks it (API RP 2GEO or ISO 19901-4) with the support reactions of the shown results.
  • Driveability checks pile driveability: soil resistance to driving (Alm & Hamre) and blow count.

Installation

Command (Offshore design)What it does
LiftSingle-hook lift on the selected padeye nodes: sling loads, slings and shackles (DNV-ST-N001 §16)
Sea transportBarge motion cases and sea-fastening forces at the selected supports (DNV-ST-N001 §11)
Load-outSupport reactions for level tolerances at the selected skid or trailer nodes (DNV-ST-N001 §7)
UpendingUpending by the crane hook at the selected node: hook load, buoyancy and stability
LaunchJacket launch from a barge along the runner between the two selected nodes

Floating bodies

A floating body is a rigid hull. Offshore › Floating › Floating body (rigid hull)… adds one; the selected nodes (tower base, fairleads) are attached to it rigidly.

FieldMeaning
Name in the BEM fileMust match the body group of the .h5 file (“body1”, “body2”, …)
Hydrodynamic data (.h5)A BEMIO .h5 file (from Capytaine, WAMIT or NEMOH), a full path or builtin:…
Mass, CoG, Ixx, Iyy, IzzThe CoG must be the equilibrium position of the BEM data
Display shapeSphere, Cylinder, Box, Spar with heave plate, or None

A body's Properties also set linear or nonlinear hydrostatics (nonlinear uses a hull mesh), linear and quadratic damping, hull drag members (columns, pontoons, braces), heave plates, wind and current coefficient tables, mean drift coefficients, and slow drift (Newman approximation) in irregular seas.

Other commands in Offshore › Floating:

  • Body coefficients by Nemoh or Capytaine…: computes the coefficients of the bodies: frequency range, number of frequencies, wave headings, mean drift (Capytaine), waterline lid (Nemoh) and mesh resolution.
  • Body coefficients from a NEMOH run…: uses a finished NEMOH run (Nemoh.cal and its results folder).
  • Hull mesh of the body from a file…: Nemoh .dat, WAMIT .gdf or STL panels. Save the body hull mesh… writes .dat or .gdf.
  • Body coefficients plots: added mass, radiation damping and excitation of a body.

Floating hulls run in Dynamic, RAO and Offset studies. They are held in place in static studies.

Mooring lines

Select one fairlead node and click Offshore › Floating › Mooring line. The line runs to an anchor on the seabed and is laid out on its static catenary. The Output panel gives the static fairlead tension and the length on the seabed, or says the line is taut.

FieldMeaning
Line typestudless chain, studlink chain, six-strand wire, spiral strand wire or polyester rope
Chain gradeR3, R4 or R5
Nominal diameterLine size
Anchor distance, direction to the anchorHorizontal, from the fairlead
Line length, segmentsLonger than the anchor distance for a catenary

Buoy adds a buoy or clump weight (mass and displaced volume) on a selected line node. In Dynamic studies the lines are FE cables (ANCF) with seabed contact, or MoorDyn lumped-mass lines. A study can remove broken lines (damaged condition) or break one line at a given time (transient condition).

Offshore design › Mooring check checks line tensions against the minimum breaking strength (API RP 2SK or DNV-OS-E301) and anchor loads, for the intact, damaged or transient condition.

NEMOH hydrodynamics

NEMOH computes the hydrodynamics of a hull by the boundary element method: added mass, radiation damping, wave excitation and motions (RAOs). It runs as a separate program. The commands are in Offshore › Floating, group Hull hydrodynamics — NEMOH.

  1. NEMOH hull from a template… (cylinder, spar, barge, semi-submersible, hemisphere), or Hull from the model… (solids, or shell surfaces closed below the water, meshed with gmsh).
  2. Mesh the bodies and Check.
  3. Analysis › Choose the analysis… › Floating hull, then Run analysis (F5). It runs first order, and second order (QTFs) when that is on.
  4. Hydrodynamics plots and Bodies in waves (the bodies animated with their RAOs in a regular wave).
  5. Export WAMIT files (.1, .3, .hst, and .12d, .12s, .9 with QTFs) for OpenFAST HydroDyn, or Use in the OpenFAST model to set HydroDyn's PotFile of the open OpenFAST model.

A NEMOH project opened with File › Open (Nemoh.cal) becomes part of the project. Remove the NEMOH project takes it out; its files stay on disk.

Wind turbines and OpenFAST

A rotor in the FEA model

Select the tower-top node and click Offshore › Renewables › Rotor (thrust curve or AeroDyn). The rotor acts in Dynamic studies.

Rotor modelWhat it does
Thrust curve (aerodynamic damping)Quasi-steady thrust on the wind relative to the hub, so tower and platform motion is damped (also in the RAO). Diameter, rated speed, thrust coefficient, or a thrust table.
OpenFAST AeroDyn, two-way (NREL 5 MW)AeroDyn and InflowWind (OpenFAST v5) compute the blade loads from the moving rotor every step. Controller: Baseline (NREL 5 MW), ROSCO 2.10 (NREL 5 MW tuning) or none.
Thrust load history (one-way)A thrust history from the curve and a steady or Kaimal wind, applied as a load

Tower-top loads from an OpenFAST run… imports tower-top load histories from an OpenFAST .out file at the selected node (one-way).

Running OpenFAST on the model

For a model with a rotor and a floating body:

  • Floating body as an OpenFAST deck (NREL 5 MW)… saves the NREL 5 MW on the model (tower, floating body, mooring lines, sea state) as an OpenFAST v5 input deck.
  • Run the floating body in OpenFAST (NREL 5 MW) runs it (ElastoDyn, ServoDyn, AeroDyn, HydroDyn, MoorDyn) and charts the platform motions, rotor, generator power, fairlead tensions and tower base moments.

Both ask for the simulated time, time step, sea state, controller, Kaimal turbulence and VTK animation frames. Open the run folder in the FEA Viewer for all channels.

OpenFAST models

The Renewables submenu also works on OpenFAST models directly:

  • Support and turbine from a template… draws a support from its parameters (land, monopile, tripod, jacket, spar, semi, TLP, barge), or starts from its r-test model. Import an OpenFAST model… draws an existing model to edit and run again.
  • Wind…: steady wind, turbulent wind made by TurbSim, or IEC wind gusts and extreme events.
  • Tower modes, Airfoil library, Check model (F7) and Write the animation.
  • Results: Plots and statistics, Load the animation, Compare with baseline… and the IEC load cases.

Choose Analysis › Choose the analysis… › Wind turbine; Run analysis (F5) then runs OpenFAST.

Wave energy

Offshore › Renewables › PTO adds a power take-off between a floating body and another body or the seabed: point, axis, type (Linear or Hydraulic (force limit)), damping, stiffness and force limit. Dynamic studies record the absorbed power (Chart › PTO power). After an RAO study, Offshore design › Power matrix gives the mean power for each Hs and Tp and, with a scatter diagram, the annual energy. See the wave energy tutorial.

Reports and exchange

  • File › Report (Ctrl+P) includes an Offshore section with the environment and the offshore results and checks, plus a picture of the 3D view as you left it.
  • Export writes the model or the shown results for Abaqus, Nastran, VTK or CSV, and a SESAM input interface file (.FEM).
  • Import reads SACS models (sacinp), Abaqus and Nastran files.

Verification

Checks run against closed-form results, reference programs and published definitions. A selection:

CheckReferenceAgreement
Inertia and drag force on a cylinder in a small Airy waveClosed form< 1 %
Floating sphere decayHydroChrono referencePeriod < 1 %, first trough < 5 %
RM3 float and spar heave, PTO power (regular 2.5 m, 8 s)WEC-Sim regression run≤ 1.1 %
OC4 mooring vertical load and stiffnessOC4 phase II definition (NREL/TP-5000-60601)0.8–6.3 %
NREL 5 MW rotor at 11.4 m/s, 12.1 rpmAeroDyn's own driver< 3 %
NEMOH: cylinder; sphereAquaplus; WAMIT≤ 5 %; ≤ 6 %
OC4 steady state: rotor; fairleads; platform pitchOpenFAST≤ 2 %; ≤ 2.5 %; +12 % (open)

Limitations

  • Waves on floating bodies use linear theory, whatever regular theory is selected.
  • Morison loads act normal to members only (no axial Froude–Krylov). Added mass is lumped isotropically at the nodes. Coupling in time is explicit.
  • Floating hulls: first-order potential flow plus mean drift and Newman's slow drift (no full QTFs in the FEA solver). Hulls are rigid and are held fixed in static studies.
  • Soil: API or PISA backbone curves; cyclic degradation as a reduction, no hysteresis. Lateral springs along global X and Y and axial springs along Z, so raked piles are approximate.
  • Plastic hinges are rigid-plastic with the N–M interaction only.
  • OpenFAST rotors in the FEA solver: rigid blades, no tower shadow or nacelle drag, no gyroscopic moments, a simplified NREL 5 MW baseline controller, loads exchanged once per step. Only the NREL 5 MW aerodynamic data are bundled.
  • The OpenFAST deck and run commands need a floating body; fixed-bottom structures are not written by them.
  • The thrust-curve rotor is quasi-steady (no dynamic inflow). Imported OpenFAST tower-top loads are one-way.
  • The PTO force limit applies in the time domain only.
  • The seabed is flat, at the water depth.
  • Mooring cables have no meaning in Modal studies (no tension in the undeformed state); use Nonlinear, Wave or Dynamic.
  • HHT can fail with light mooring lines on a floating hull; implicit Euler is the default there.