1

Start from the jacket frame

The starter is a ready-made jacket frame: legs, X-braces, horizontal frames, piles, a deck and 3000 t of topsides load. It has no offshore data yet. You add that in the next steps.

  1. Click Offshore › Workflows (F1), open Offshore structures and choose Fixed jacket platform.
  2. Click Load the jacket frame. It opens as a new, unsaved project.

Each step in the panel has buttons for its commands and ticks itself when it is done. To model your own structure instead, draw members with Line or Polyline, give them a section with Beam, or import an Abaqus or Nastran file.

To compare with the finished model at any time, use File › Samples › Four-leg jacket.

2

Check sections and materials

Offshore code checks apply to tubular members, so their section must be a Pipe profile.

  1. Open Explorer › Sections to see the diameters and wall thicknesses.
  2. Click a member to see its section in Properties.
  3. To add standard sections, use Sections (the regional steel catalogs).
3

Review loads and supports

The starter has gravity (self-weight) and the topsides weight and wind as forces on the deck nodes. To add a force, select nodes in the 3D view, then click Force.

A jacket needs no fixed supports. Once the piles are marked, the soil springs below the mudline hold it.

4

Create the offshore environment

The environment holds the water depth, the still-water level (MSL) and the design code. Members below MSL then get buoyancy, and wave and current loads by the Morison equation.

  1. Click Offshore › Environment and enter the values below. The sea and the seabed appear in the 3D view.
FieldValue
Design codeAPI RP 2A-WSD
Water depth60 m
MSL elevation0 m

The drag and inertia coefficients (Cd, Cm), the wave kinematics factor and the current blockage factor are in the Properties of the Offshore folder in the Explorer.

5

Add the current

Current is added to the wave particle velocities. A 1/7 power law profile is typical: fastest at the surface, slower near the seabed.

  1. Click Offshore › Current and enter:
FieldValue
Surface speed1.2 m/s
Speed at the seabed0.3 m/s
Heading0° (same as the wave)
ProfilePower law (1/7)
6

Add marine growth

Marine growth makes members thicker, so they get more wave load, and heavier. It is given by depth zone.

  1. Click Offshore › Marine growth and enter:
FieldValue
Thickness0.05 m
From height above MSL2 m
To height above MSL−40 m
Density1325 kg/m³
7

Define the design wave

The 100-year storm is a regular design wave. Stokes 5th order suits this depth. The Wave analysis later moves this wave through the structure.

  1. Click Offshore › Design wave and enter:
FieldValue
Wave theoryStokes 5th order
Wave height H18 m
Period T14 s
Heading0°
8

Add the soil

Soil layers produce the API p-y (lateral), t-z (shaft friction) and q-z (end bearing) springs on every pile node below the mudline. Here one clay layer covers the pile depth, with strength increasing with depth.

  1. Click Offshore › Soil layer and enter:
FieldValue
Soilclay
Top / bottom depth0 m / 90 m
Submerged unit weight γ′8.5 kN/m³
cu at top / bottom40 / 280 kPa
9

Mark the piles

Only curves marked as piles get soil springs.

  1. Click Select the pile curves in the workflow step. It selects the four curves with a “Pile” section.
  2. Click Offshore › Piles.

Clicking Piles again on marked curves unmarks them. A curve's Properties also have a Pile (soil springs) setting.

10

Set member hydrodynamics (optional)

The legs are grouted around the piles and flooded: water inside, so the bore gives no buoyancy and is not checked for hydrostatic collapse.

  1. Click Select the legs in the workflow step.
  2. Click Offshore › Flooded.

Each member's Properties also hold the drag and inertia coefficients and the effective length factor K used by the buckling check.

11

Check the mesh

The mesh is built from the model. Solving rebuilds it whenever members, piles or lines change.

  1. Show mesh draws it over the model.
  2. Divisions… sets the number of elements of a member.
  3. Check quality lists any disconnected nodes or bad elements.

The status bar shows “Mesh: up to date” when the mesh matches the geometry.

12

Run the wave analysis

The Wave study moves the design wave through the structure at 36 positions over one period. It finds the positions with the highest base shear and overturning moment and solves them with the soil springs.

  1. Click Offshore design › Wave. Progress is shown while it runs, and Esc cancels.

The model locks once it has results. To edit it again, click Unlock model (this removes the results).

13

Review the results

  1. Look at the deflected shape (Displacement), the axial forces (Member forces) and the reactions.
  2. Animate plays the wave positions.
  3. The Chart plots base shear and overturning moment against wave position.
  4. The Results panel chooses the wave position and the scale, and lists the extreme values. Click a member to read its values.
14

Check members and joints

Code check runs the API RP 2A-WSD checks on the shown results: axial, bending, combined and hydrostatic checks for every tubular member, and punching shear for the brace–chord joints. For the storm, the one-third allowable increase applies.

  1. Click Offshore design › Code check. Members are coloured by utilization.
  2. Click Check table. It lists the highest values first.

If a member fails, unlock the model, choose a larger section (or change K in its properties), then run the wave analysis again.

[SCREENSHOT] The jacket coloured by API RP 2A-WSD utilization, with the Check table
15

Create the report and save

Report builds a report with the model, materials, sections, loads, mesh, the offshore environment and the results: the design wave results and the API member and joint checks. Save it as a web page, or print it to PDF.

  1. Set up the 3D view first. The report includes a picture of it.
  2. Click File › Report.
  3. Save the project (Ctrl+S). Export writes the model or the shown results for other programs (Abaqus, Nastran, VTK, CSV), or a picture of the 3D view.

What you learned

  • The environment, current, marine growth and design wave come from the Offshore menu.
  • Soil layers give API p-y, t-z and q-z springs only on curves marked as Piles.
  • Flooded members have no bore buoyancy and no hydrostatic collapse check.
  • The Wave study and Code check are on the Offshore design menu.