Start from the monopile and tower
The starter has a 6 m monopile from 60 m below MSL to the transition piece, a 5 m tower to the 90 m hub, a 350 t rotor-nacelle mass (a short dense element) and a 1.5 MN rotor thrust. It has no offshore data yet.
- Click Offshore › Workflows (F1), open Offshore structures and choose Offshore wind monopile.
- Click Load the monopile. It opens as a new, unsaved project.
The finished model is File › Samples › Offshore wind monopile. It uses PISA soil springs for the pile.
Review masses and loads
Mass matters for the natural frequency, so check that the rotor-nacelle mass and the tower are right. The thrust acts at the hub in +X, the same direction as the waves.
- Click the members and the load to see their values in Properties.
Create the offshore environment
- Click Offshore › Environment and enter the values below.
| Field | Value |
|---|---|
| Design code | ISO 19902 |
| Water depth | 25 m |
| MSL elevation | 0 m |
Add current and marine growth
Add the current profile first, then marine growth: 50 mm from 2 m above MSL down to the seabed.
- Click Offshore › Current.
- Click Offshore › Marine growth.
| Field | Value |
|---|---|
| Current at the surface / seabed | 1.0 / 0.2 m/s, power law |
| Growth thickness | 0.05 m |
| Growth from / to | 2 m / −25 m |
| Growth density | 1325 kg/m³ |
Define the design wave
In 25 m of water a 12 m wave is steep and nonlinear, so use the stream function theory. It is valid at any depth.
- Click Offshore › Design wave and enter:
| Field | Value |
|---|---|
| Name | 50-year design wave |
| Wave theory | Stream function |
| H / T | 12 m / 12 s |
| Heading | 0° |
Define the storm sea state
An irregular sea is a random sea from a wave spectrum. It is used in the time-domain (Dynamic) analysis, where the turbine's own vibration matters.
- Click Offshore › Irregular sea and enter:
| Field | Value |
|---|---|
| Name | Storm sea state |
| Spectrum | JONSWAP |
| Hs / Tp | 6.5 m / 11 s |
| γ | 3.3 |
| Random seed | 7 |
Add the soil layers
Add two layers, one after the other. Each new layer starts at the bottom of the previous one.
- Click Offshore › Soil layer twice and enter:
| Layer | Values |
|---|---|
| Layer 1 | sand, 0–8 m, γ′ 10 kN/m³, φ 36°, dense |
| Layer 2 | clay, 8–45 m, γ′ 9 kN/m³, cu 80 → 200 kPa |
Mark the monopile as a pile
- Click Select the monopile in the workflow step. It selects the curve with the “MP” section, the part that goes below the mudline.
- Click Offshore › Piles.
In the pile's Properties, Pile soil model chooses between API p-y / t-z / q-z and PISA (monopile). PISA needs the small-strain shear modulus G0 in the soil layers.
Check the mesh
Show mesh draws the mesh over the model. Divisions… sets the number of elements of a member, and Check quality lists disconnected nodes or bad elements.
Check the natural frequency
A soft-stiff monopile must have its first natural frequency between the rotor frequency (1P) and the blade passing frequency (3P), with a margin. Otherwise the rotor can make it resonate. Modal includes the added mass of the surrounding water and the soil springs.
- Click Offshore design › Modal.
- The Chart lists the frequencies, and Animate shows each mode shape.
Use your turbine's rpm range: 1P = rpm / 60, 3P = 3 × 1P. The workflow figure shows the bands of a 6.9–12.1 rpm rotor (NREL 5 MW type).
Run the design wave
The Wave study moves the 50-year wave through the pile, with the current, marine growth and the nonlinear soil springs, using ISO 19902 load factors (1.1 × permanent + 1.35 × environmental). Running another study keeps the earlier results.
- Click Offshore design › Wave.
Run the storm in time domain
A Dynamic study runs 60 s of the JONSWAP storm, including the structure's own vibration.
- Click Run storm (Dynamic, 60 s) in the workflow step. It creates the study “Storm 60 s” (irregular sea, 60 s, 0.1 s steps) and runs it.
- Open the Chart to see the time histories.
Analysis › Linear dynamic runs the first Dynamic study. Change its sea state and duration in the study's Properties (Explorer › Studies).
Check the monopile (ISO 19902)
The check uses the shown results.
- Click Show the Wave results in the workflow step.
- Click Offshore design › Code check. The ISO 19902 tubular checks run for every element of the pile and tower.
- Click Check table to read them.
Create the report and save
File › Report builds a report with the model, the offshore environment and the results: the design wave forces, the natural frequencies and the ISO 19902 checks. Save it as a web page, or print it to PDF. Save the project with Ctrl+S.
What you learned
- Layered soil: each new layer starts where the last one ends.
- The first natural frequency from Modal must sit between 1P and 3P.
- A regular design wave for the Wave study, an irregular sea for Dynamic.
- Code check always works on the results that are shown.